Stránka 356 z 1,179. Nalezeno 11,781 výsledků (0.136 vteřin)
.5.3.10 Digitální vstupy v2.26
. Each port can be controlled via Automation. Press the UNBLOCK button, disable the function or reset the configuration factory values to unblock the switches.5.3.1 Spínače v2.27
. 2N® IP Vario – na konfiguračním konektoru je potřeba nastavit interní napájení a spínací relé. 2N® IP Force – bezpečnostní relé se připojuje na svorky DOOR … . 2N® IP Vario – be sure to set the internal power supply and switching relay on the configuration connector. 2N® IP Force – the security relay is connected2N_LiftNet_User_Guide_EN_1.9.pdf
panel edge and tighten applying light force. Mounting Just drill holes into the lift cabin wall as indicated in the drawing below or as printed 1:1 on the … you keep the factory settings. For deactivation, voltage application or contact closing is necessary. To change the settings use parameter 916 for ST and the.3.2 Licencování funkcí v2.28
protokolu. Od SW verze 2.25 lze kodek G.729 použít bez zadání licenčního klíče. 2N® IP Verso, Base, Solo, Vario, Force, Safety a Audio Kit s Video Kitem toto … protocol to be used. 2N® IP Verso, Base, Solo, Vario, Force, Safety and Audio Kit with Video Kit do support this licensing scheme in full. User only needs.3.2 Licencování funkcí v2.26
bez zadání licenčního klíče. 2N® IP Verso, Base, Solo, Vario, Force, Safety a Audio Kit s Video Kitem toto licenční schéma plně podporují. Uživatel musí … ® IP Verso, Base, Solo, Vario, Force, Safety and Audio Kit with Video Kit do support this licensing scheme in full. User only needs to observe which licenses.2. Expresní průvodce základním nastavením v2.25
(odkaz níže). Pokud ve vaší síti není DHCP server, musíte nastavit 2N Access Unit na statickou IP adresu pomocí RESET tlačítka, viz Instalační manuál … in your LAN, use the 2N Access Unit RESET button to set the static IP address mode; refer to the respective Installation Manual. Your unit address will then be.2. Expresní průvodce základním nastavením v2.18
manuál (odkaz níže). Pokud ve vaší síti není DHCP server, musíte nastavit 2N® Access Unit na statickou IP adresu pomocí RESET tlačítka, viz Instalační manuál … DHCP server in your LAN, use the 2N® Access Unit RESET button to set the static IP address mode; refer to the respective Installation Manual. Your unit address.2. Expresní průvodce základním nastavením v2.16
manuál (odkaz níže). Pokud ve vaší síti není DHCP server, musíte nastavit 2N® Access Unit na statickou IP adresu pomocí RESET tlačítka, viz Instalační manuál … there is no DHCP server in your LAN, use the 2N® Access Unit RESET button to set the static IP address mode; refer to the respective Installation Manual. Your unit5.3 Použití
a Minimum udávají povolený rozsah nastavovaných hodnot. Výchozí hodnota poukazuje na hodnotu parametru, která je nastavena z výroby nebo po provedení factory resetu … . Například u IP kamery se nenastavují parametry obrázku ale pouze web link obrázku. Nastavení kvality a komprese se musí nastavit v kameře před jejím připojením.5.4.1 Řízení přístupu v2.43
software factory reset or different configuration upload does not result in a change of the access blocking setting. It is only the hardware factory reset using the … in the device memory and can be retrieved via an HTTP request sent to api/lpr/image available in 2N Access Commander. The software factory reset or different