Stránka 587 z 1,178. Nalezeno 11,780 výsledků (0.099 vteřin)
.5.5.7 Údržba v2.26
do úplného výchozího stavu, použijte příslušnou propojku nebo tlačítko reset, viz instalační manuál k příslušnému interkomu. Obnovení výchozího nastavení vymaže … – provede restart interkomu. Celý proces restartu trvá asi 30 s. Po dokončení restartu, kdy interkom získá IP vlastní adresu, se automaticky zobrazí přihlašovací.3CX Phone System v1.9
there you have to allow codec H.263 on the first position and disable the rest, see (Pic. 3). 2eng.jpg 4. To verify that you successfully register 2N IP … have to allow codec H.263 on the first position and disable the rest, see (Pic. 3). 2cz.jpg 4. To verify that you successfully register 2N IP intercom terminal.3CX Phone System v1.8
to allow codec H.263 on the first position and disable the rest, see (Pic. 3). 2eng.jpg 4. To verify that you successfully register 2N IP Intercom terminal … Content About 3CX Phone System http://www.3cx.com/ 3CX Phone System for Windows is a software-based IP PBX that replaces a proprietary hardware2N_Easy_Gate_PRO_User_Guide_EN_1.4.pdf
factory default setting. The tone frequency is 425 Hz. User Guide 2N® EasyGate PRO 9 / 72 • • • • • • • • • • • • • • • • • • • • • Dial tone continuous or … necessary. If EasyGate is not reset after the PCManager UNI is terminated, switch the system off and on again. User Guide 2N® EasyGate PRO 16 / 72 1. 2. 3. 42N_Easy_Gate_PRO_User_Guide_EN_1.4.pdf
(UMTS) gateway sends tones to the telephone line to indicate the line status. Following part describes the factory default setting. The tone frequency is 425 … instructed so by the PCManager UNI during this timeout, EasyGate remains in this mode as long as it is necessary. If EasyGate is not reset after the PCManager UNI is2N_Easy_Gate_PRO_User_Guide_EN_1.4.pdf
(UMTS) gateway sends tones to the telephone line to indicate the line status. Following part describes the factory default setting. The tone frequency is 425 … instructed so by the PCManager UNI during this timeout, EasyGate remains in this mode as long as it is necessary. If EasyGate is not reset after the PCManager UNI is2N_Easy_Gate_PRO_User_Guide_EN_1.4.pdf
(UMTS) gateway sends tones to the telephone line to indicate the line status. Following part describes the factory default setting. The tone frequency is 425 … instructed so by the PCManager UNI during this timeout, EasyGate remains in this mode as long as it is necessary. If EasyGate is not reset after the PCManager UNI is.5.3.2 api config factoryreset v2.40
/config/factoryreset function resets the intercom factory values with a delay of approx. 15 s; do not reset or switch off the intercom during this interval. Example … žádné parametry. Funkce /api/config/factoryreset nastavuje interkom do výchozího stavu se zpožděním cca 15 s, během tohoto intervalu se interkom nesmí resetovat3.6 GSM Menu
the following actions: Reset – restart the selected GSM/UMTS module; Unlog – log the SIM card out of the selected GSM/UMTS module. Initiate recharging of … assignments of the selected GSM channels. Unlink SIMs from selected GSMs – push the button to cancel the SIM hard assignment. Reset selected – push the button.3.6 GSM Menu v14.0
the following actions: Reset – restart the selected GSM/UMTS module; Unlog – log the SIM card out of the selected GSM/UMTS module. Initiate recharging of … assignments of the selected GSM channels. Unlink SIMs from selected GSMs – push the button to cancel the SIM hard assignment. Reset selected – push the button