4.2 Non-Stop Service Instructions for Use
DTMF Control during the Call
Where Automatic dialing with confirmation is enabled, it is possible to use tone dialing during the call to control the ST in accordance with the table below. For convenience, commands 1 to 5 are arranged in the order they are usually used in.
DTMF char | FUNCTION DESCRIPTION | ||
| It is a confirmation notifying SingleTalk (hereinafter referred to as ST) that the call was successful. ST mutes the message playback, sends out the confirmation signal and the call continues until the end of the timeout and the following commands can be used | ||
| Message playback muting. CAUTION: Now that the SW has been changed, it is no more necessary for the call! | ||
| Repeated playback of the voice recording module for 1 message repetition | ||
or
| Call prolongation: the call is prolonged up to 30 seconds after this command in case it ended earlier. It can be used repeatedly. | ||
or
| Call termination. | ||
| ST sends identification but the connection is not confirmed. Used for the LiftManager only. | ||
to and
| These digits are interpreted as the switch control password beginning. |
(Automatic dialling with confirmation)
Note
- When the message is being played back, it is impossible to speak into the ST microphone! Hence, to talk with the person in the lift, the service must always use function 2 (muting) or wait till the ST stops repeating the message.
- The above-stated commands may not be accepted in case they are sent during the message and the connection is of a poor quality. Therefore, the ST inserts a 3-second pause between the repeated message, during which the receiving of DTMF commands is absolutely undisturbed.
Switch Control
The switch (if available) can be used during outgoing and incoming calls. The switch can be activated using a pre-defined password; the format is
password (the maximum password length is 16 digits). The ST confirms the switch activation and turns it on for the pre-defined period of time (1 to 10 seconds). It is not possible to talk during the switch on-status and the ST signals this action with tones as per the signaling review table. The call is terminated 30 seconds after the switch activation.
Tip
- The switch can be used, for example, for resetting the lift Each switch can be controlled with up to 10 variable passwords. A new feature is that the password can be entered without asterisks too if it starts with 6 to 9, or 0. (This limit applies to the use of Automatic dialing with confirmation.)
ST Signalling Overview
ST uses variable signals to communicate with the operating personnel during programming, calls, and so on. For an overview of the signals including meanings refer to the table below:
SIGNAL | NAME | MEANING | |
---|---|---|---|
| Confirmation | Sent during an incoming call to the line immediately after off-hook (the calling party hears it). | |
| Rejection | Whenever a non-programmed button is pressed. | |
| Storing | Remote switch activation end. | |
| Hang-up | Sent close before the call end (in all cases). | |
Long continuous tone | Deleting | Sent during dialing memory clearing, or full initialization | |
"Attention, your call is being terminated" | Signals during an outgoing or incoming call that the maximum call duration will elapse in 10 seconds. | ||
"Wait please..." | Programmable connection-waiting message. | ||
"Communicator No. ... is calling ." | Programmable identification message. |
Survey of Messages
The table below includes a survey of language versions for standard announcements. English is selected by default. To select another language use parameters 976 and 977.
Value of Parameter | Language selection – English version | End of call message | Outgoing call message | |||
ID message.Parameter 975 must contain digit 2, 3 or 5 | Confirmation message. Parameter 975last digit = 5 | Checking call message | ||||
0 | Tone signal |
| off | off | off | |
1 (default value) | English | Attention, your call is being terminated | Communicator number.......... is calling | Connection confirmed | Checking Call | |
2 | German | Achtung, das Gespräch wird beendet | Es ruft das Notruftelefon Nummer……an. |
| Der Kontrollanruf | |
3 | Portuguese | ............. | ............. |
| .............
| |
4 | Dutch | ............. | ............. |
| ............. |
Value of Parameter | Language selection – English version | Outgoing call message | Note |
0 | Tone signal | off |
|
1 *) | English | Wait please | |
2 | German | Warten Sie bitte | |
3 | Portuguese | ............. | |
4 | Dutch | ............. |
Caution
- The Czech version and custom specific models has another set of languages.
ST Identification
If parameter 974 is filled with a number, and parameter 975 contains digit 2, 3 or 5, ST identifies itself automatically by replaying "Communicator number... is calling". Use parameter 976 to set the language for lift number identification.