4.3 LOGs
For the current LOG records see the Gateway / Gateway control – LOG file section or use the AT&L AT command for Telnet sessions. The following list of LOG statuses is universal and some LOGs may not be included in 2N® VoiceBlue Next:
Type | Text | Description |
POWER | [Power on] | System switched on |
[Power off] | System switched off | |
[Warm boot] | Restart of system, unknown cause | |
[Watchdog] | Restart of system by watchdog | |
[BKPT code] | CPU error: break code detected | |
[Stack error] | CPU error: stock integrity failure | |
[Divided by zero] | CPU error: dividing by zero | |
[RETI code] | CPU error: illegal using of instruction reti | |
[NMI intr] | CPU error: wrong interrupt | |
[VOID intr] | CPU error: wrong interrupt | |
[Upgrade reset] | Start of upgrade firmware procedure | |
[Software reset] | Reset by AT commands (at&fres…) | |
INIT | Eeprom | Initialisation of eeprom (configuration) |
Flash | Initialisation of flash memory (firmware) | |
HW–ERR | (##…address of chip, RD…read value/WR…expected value) | |
Codec ##,RD/WR | Error in initialisation of codec on GSM,AUX board | |
COM2 #####,RD/WR | Error in initialisation of COM2 on AUX board | |
Duart #####,RD/WR | Error in initialisation of serial controller on GSM board | |
Hscx #####,RD/WR | Error in initialisation of HDLC controller on AUX board | |
Pri #####,RD/WR | Error in initialisation of PRI controller | |
SYSERR | User stack error! | SW error: stock integrity failure |
BRDIN | #08 TYP STS | Board inserted (number of gsm board, type, status) |
BRDOUT | #08 TYP STS | Board disconnected |
BRDRES | #08 TYP STS | Reset the board by AT command |
ALL GSM RESET CMD | Reset all GSM boards by AT command | |
SYSTEM RESET CMD | Reset the system by at&bsys command | |
L1–ERR | (reserved) | |
L2–ERR | Error of ISDN layer 2 by Q.921 | |
A: unsol.RX(F) | Received packet RR,RNR,REJ with unexpected bit F=1 | |
B: unsol.DM(F) | Received packet DM with unexpected bit F=1 | |
C: unsol.UA(F) | Received packet UA with unexpected bit F=1 | |
D: unsol.UA(–) | Received packet UA with unexpected bit F=0 | |
E: unsol.DM(–) | Received packet DM with unexpected bit F=0 | |
F: peer re–est | Received packet SABME in status OKEST | |
G: repeated SABME | Repeated unsuccessful send of packet SABME | |
H: repeated DM | Repeated unsuccessful send of packet DM | |
I: failed (TIMREC) | Unsuccessful breaking-up of status TIMREC | |
J: N(R) error | Received wrong value N(R) – numbering of packets | |
K: recv.FRMR | Received packet FRMR (information about error) | |
L: undef.frame | Received packet of unknown type | |
M: (I field) | Received wrong I-packet (numbered packet) | |
N: frame size | Received packet with wrong length | |
O: N201 error | Value N201 was exceeded (max length of packet) | |
L3–ERR | tout sts # (p##) | Error of isdn layer 3: timeout in status # on channel p## |
G2–ERR | ATD/ERROR init (g##) | Error of isdn layer 2: restart of module g## after rejected command ATD by GSM network |
GSM Cause 150 (g##) | Error of isdn layer 2: restart of module g## after cause 150 was received (call barred by GSM network) | |
G3–ERR | tout sts # (g##) | Error of isdn layer 3: timeout in status # on module g## |
C4–ERR | tout sts # (p##/g##) | Error of connecting layer 4: timeout in status # on call between channel p## and GSM module g## |