7. Available Digital Inputs and Outputs

In this section, the digital inputs and outputs available on each 2N device are described.

2N IP Style

Main Unit

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input 1 on main unit
  • input2 – digital input 2 on main unit
  • input3 – digital input 3 on main unit
  • tamper – tamper switch

I/0 Module

The inputs / outputs are addressed as follows: <module_name>.<input/output_name>, e.g. module5.relay1.

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • relay1 – relay output 1
  • relay2 – relay output 2

Inputs

  • input1 – digital input 1
  • input2 – digital input 2
  • tamper – tamper switch (if installed)

Wiegand Module

The input is addressed as follows: <module_name>.<input_name>, e.g. module2.tamper

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • output1 – LED OUT output

Inputs

  • input1 – LED IN input
  • tamper – tamper switch (if installed)

2N IP One

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input 1 on main unit
  • tamper – tamper switch

2N IP Vario

Outputs

  • relay1 – relay output on main unit
  • relay2 – relay output on additional switch (if installed)
  • cr_relay1 – relay output 1 on card reader (if installed)
  • cr_relay2 – relay output 2 on card reader (if installed)

Inputs

  • cr_input1 – digital input 1 on card reader (if installed)
  • cr_input2 – digital input 2 on card reader (if installed)

2N IP Force/Safety

Outputs

  • relay1 – relay output on main unit
  • output1 – active digital output on main unit (for board version 555v3 and higher, active digital output is connected with relay output 1 in 555v2 boards)
  • relay2 – relay output on additional switch (if installed)
  • output2 – active digital output on additional switch (if installed)
  • cr_relay1 – relay output on card reader (if installed)
  • cr_output1 – active digital output on card reader (if installed)

Inputs

  • tamper – tamper switch (if installed)
  • cr_input1 – digital input 1 on card reader (if installed)
  • cr_input2 – digital input 2 on card reader (if installed)
  • input2 – digital input 2 on additional switch (if installed)

2N IP Audio/Video Kit

Outputs

  • relay1 – relay output
  • output1 – digital output 1
  • output2 – digital output 2
  • led1 – LED 1 control output
  • led2 – LED 2 control output
  • led3 – LED 3 control output

Inputs

  • input1 – digital input 1
  • input2 – digital input 2

2N IP Verso/IP Verso 2.0/LTE Verso

Main unit

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input on main unit

I/0 Module

The inputs / outputs are addressed as follows: <module_name>.<input/output_name>, e.g. module5.relay1.

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • relay1 – relay output 1
  • relay2 – relay output 2

Inputs

  • input1 – digital input 1
  • input2 – digital input 2
  • tamper – tamper switch (if installed)

Wiegand Module

The input is addressed as follows: <module_name>.<input_name>, e.g. module2.tamper

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • output1 – LED OUT output

Inputs

  • input1 –  LED IN input
  • tamper – tamper switch (if installed)

2N IP Solo

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input on main unit
  • tamper – tamper switch

2N IP Base

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input on main unit
  • tamper – tamper switch

2N SIP Audio Converter

Outputs

  • relay1 – relay output

Inputs

  • Unavailable
  • It is possible to use Event.KeyPressed: Key=%1 for events generated at LOGIC IN input

2N Access Unit

Main unit

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input 1 on main unit
  • input2 – digital input 2 on main unit
  • input3 – digital input 3 on main unit
  • tamper – tamper switch

I/0 Module

The inputs / outputs are addressed as follows: <module_name>.<input/output_name>, e.g. module5.relay1.

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • relay1 – relay output 1
  • relay2 – relay output 2

Inputs

  • input1 – digital input 1
  • input2 – digital input 2
  • tamper – tamper switch (if installed)

Wiegand Module

The input is addressed as follows: <module_name>.<input_name>, e.g. module2.tamper

The module name is configured in the Module name parameter in the Hardware / Extenders menu. 

Outputs

  • output1 – output LED OUT

Inputs

  • input1 – vstup LED IN
  • tamper – tamper switch (if installed)

2N Access Unit 2.0

Main unit

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input 1 on main unit
  • input2 – digital input 2 on main unit
  • tamper – tamper switch

I/0 Module

The inputs / outputs are addressed as follows: <module_name>.<input/output_name>, e.g. module5.relay1.

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • relay1 – relay output 1
  • relay2 – relay output 2

Inputs

  • input1 – digital input 1
  • input2 – digital input 2
  • tamper – tamper switch (if installed)

Wiegand Module

The input is addressed as follows: <module_name>.<input_name>, e.g. module2.tamper

The module name is configured in the Module name parameter in the Hardware / Extenders menu.

Outputs

  • output1 – LED OUT output

Inputs

  • input1 – LED IN input
  • tamper – tamper switch (if installed)

2N Access Unit M

Main unit

Outputs

  • output1 – digital output
  • relay1 – relay output

Inputs

  • input1 – digital input 1 on main unit
  • input2 – digital input 2 on main unit