5.7.1 Commands
The Commands folder helps you send commands via SMS if you are logged in.
 |
- Information Reading (INF) – command to send an SMS including basic information (signal, used mobile network technology, provider code and name, battery status).
- Parameter Reading (GET) – command to send an SMS including information on selected parameters.
- Parameter Change (SET) – command to change parameters in the setting.
- Password Change (PWD) – command to change the device password.
- Factory Defaults (DEF) – command to reset the device factory defaults.
- Restart (RST) – command to restart the device.
| SMS Command | SMS Format | Note |
|---|---|---|
| Read information (INF) | EG INF password | The reply includes such information as the device serial number, FW version, IMEI and IMSI, roaming status, signal strength, network supply status, battery status and remaining battery time. Set the reply contents using the INF message format parameter. In case 2 SIM cards are used in the device, the SMS reply includes two IMSIs and information related to the active SIM card only. |
| Read parameters (GET) | EG GET password | E.g.: EG GET initial_pasword 150 swg_enable sim1_pin (Send the command to get information on the My2N settings, SMS function on the device and SIM 1 PIN code.) |
| Change parameters (SET) | EG SET password numeric or text identifier=new value | This command helps you change the parameter values; configurable parameters must be assigned numbers. If set as a text, a parameter must be closed in parentheses. E.g.: EG SET initial_pasword 150=1 sgw_period=60 sim1=1234 243=(internet.t-mobile.cz) (Send the command to set the My2N service enable, set the INF message period to 60 minutes, change of SIM 1 PIN code to 1234 and set the APN.) |
| Change password (PWD) | EG PWD password_old password_new | E.g.: EG PWD initial_pasword amber The new password will be set as amber. |
| Set factory defaults (DEF) | EG DEF password | E.g.: EG DEF amber Send the command to reset the factory defaults, which is followed by the device restart. |
| Restart device (RST) | EG RST password | E.g.: EG RST amber The device will be restarted. |
| Events |
|---|
| EG EVT power=[charge|backup|fully|error] |
| EG EVT start |
| EG EVT slot=[1|2] |
| EG EVT input=[0|1] missed=<num> |
| Description | ||
|---|---|---|
| <pwd> | authorization password | |
| <new_pwd> | new authorization password | |
| <pn> | parameter (see param or param_id) | |
| <vn> | numeric value or text value in brackets (see length, size, min, max, enum) | |
| <msg> | detailed description | |
| Successful | ||
| Unknown command | ||
| Invalid password | ||
| Invalid parameters | ||
| Invalid syntax | ||
| Does not respond | ||
| Not allowed | ||
| Time limit | ||
| Error | ||
| <cmd> | the command to which it responds (DEF, RST, INF, PWD, SET, GET) | |
| <seq> | sequence counter | |
| <num> | numeric value | |
Example of parameter settings:
- EG SET pwd 100=0 sgw_ident=(EGIP 1)
Example of reading parameters:
- EG GET pwd 100 sgw_ident
| Command Feedback | |
|---|---|
| EG SET OK | Setting ok |
| EG ERR Unknown Command | A command other than SET, GET, DEF, RST, INF has been used |
| EG ERR Password | Invalid password |
| EG ERR Invalid Parameters | Invalid parameter in command |
| EG ERR Invalid Syntax | Invalid characters (spaces, equal signs, etc.) |
Caution
SMS Commands
- The commands are only valid if typed in capital letters.
- One type of command can only be sent via SMS.
- For the GET and SET commands, multiple parameters can be used at the same time separated with spaces. The parameters are set by a numeric or text identifier and can be combined. We recommend that you use numerical identifiers, as they contain fewer characters.
- The maximum SMS length is 140–160 characters. If a setting out of the allowed value range is requested or there is another error in the message, no setting will be made for any parameter.
Tip
- Refer to Subs. 5.6.1.1 for the parameter list including identifiers.